 |
|
|
|
|
The Love-Less Ash fireplace vacuums are specifically designed to remove warm to cold ash from wood stoves, pellet stoves, fireplaces and barbecues.
- Patented double filter system
- Comes complete with a FIRE RETARDANT PRIMARY FILTER.
- Cleaning rod and pliable filters allow cleaning without removing the lid.
- 5 foot. flame retardant hose allows ash to pass through the hose to the canister without damage to the hose.
- Designed for conventional stoves and fireplaces as well as pellet and corn burning stoves.
|
Frequently Asked Questions about the Loveless
Ash Fireplace Vacuum
The nozzle gets clogged on the fireplace vacuum and I can’t take out the
ash. Or - I have to use my fingers to get the ash off the nozzle. Why?
Put the crimped end of the nozzle directly onto
the firebrick of the conventional stove or fireplace and move it back and forth
or in a circular motion. This cleans a small area and then the nozzle is moved
from the cleaned area to the ash surrounding it. The nozzle is kept right on the
brick.
The ash is actually removed from the bottom and not the top. This helps the ash
to move quickly along the hose and keeps the nozzle opening free and clear of
debris. As the ash is being taken into the vacuum, larger pieces of wood or
charcoal, etc. can be moved out of the way and left in the stove and burned at a
later time.
Customers should never have to use their hands or fingers to remove particles
stuck on the end of the nozzle. If you come across this situation – the
customer is holding the nozzle above the ash and it is balling up on the end of
the nozzle because all the ash is trying to go through at the same time.
This fireplace vacuum will only allow fine ash to travel through the nozzle and
hose. Larger particles or materials are not meant to be removed with this
vacuum.
Why can’t I take out large pieces?
The fireplace vacuum is designed to remove only ash. The larger pieces should be
left in the stove or fireplace and burned at a later time.
Why is the hose so stiff on the Loveless Ash fireplace vacuum?
The hose is a bit unwieldy because it is made to handle the possibility of warm
coals and embers. It is flame retardant. It should be positioned so that the
hose has a natural curve from the vacuum to the nozzle that is put inside of the
stove or fireplace. The customer should not position the vacuum so that a kink
forms in the hose or else it will cut off the suction. The motor is cooled by
external air so if the nozzle does become clogged, it will not damage the motor.
I don’t have any suction with the fireplace vacuum.
Usually, the reason for poor suction is that the vacuum has been used and a
crust of ash has formed on the outside of the primary filter and it cannot
breathe properly. The customer assumes that the vacuum is then not working.
Cleaning procedure for filters - Remove the brass nipple and cap from the top of
the lid and then raise the metal rod or "NOGGLE" approximately ½ inch
and rock it from side to side so that the ash that has collected on the outside
of the primary filter can be shaken off and suction will resume as before.
The nipple and cap must be screwed back into place, just finger tight. The
vacuum needs to be maintained so the nipple and cap must be in place, when in
operation.
If the customer has used the fireplace vacuum cleaner extensively and loses
suction, the reason is usually that the secondary filter has become coated with
very fine ash, to the point that it needs to be cleaned. This will usually
happen after 60-80 gallons of ash has been collected by the vacuum.
To clean the secondary filter, the primary filter needs to be taken off and the
secondary filter needs to be vacuumed off by another vacuum source, Usually a
home vacuum. If there is any residual ash caught inside the two filters, this is
a good time to take that out as well. The filters are held on by hose clamps
that only require a flat blade screwdriver.
The Cheetah II is designed with the small cage part of the lid mounted on snap
springs so when the vacuum is turned on the basket will rest against the cage
and compress the springs. When the vacuum is turned off the springs snap back
and clean the secondary filter without the customer ever being aware of it. This
is why the customer can use it for such a great length of time without even
needing to look at the secondary filter. This new design is extremely user
friendly.
Can I wash the filters on the fire place vacuum?
No. Both filters are specially coated and if they are washed, the finish will be
removed and they will not operate properly.
There are holes in my primary filter, what are they from?
The customer has vacuumed up HOT COALS and/or LIVE EMBERS. This usually happens
with pellet stoves. If pellets are not totally dead, the forced air from the
vacuum will re-ignite them and they could come to rest against the side of the
primary filter and scorch a hole through it. If unburned fines are removed from
a pellet stove and they coat the primary filter and then a live pellet is pulled
through the vacuum and it happens to come to rest against the filter, it will
set the fines on fire and a large area of the filter will be scorched. In a
conventional stove this same thing can happen if the embers are still burning
and too many embers are removed without the insulation of dead ash.
Can I use this fireplace vacuum cleaner for other things?
No. This vacuum is only designed for ash. If it is used as a regular shop vacuum
for materials that could be flammable and then used in a stove and live embers
are removed, a fire could result.
How often should I change the filters?
Changing of the filters is determined by the use and care the are given. We
recommend that the filters be changed after about 100 gallons of ash have gone
through the vacuum.
How full can I fill the fire place ash vacuum?
We recommend emptying the vacuum when the ash level is as high as the port on
the side of the canister. When the ash gets this high, the customer will usually
notice a slight reduction in suction because of the reduced area for depositing
the ash in the canister.
Can I take out HOT COALS?
No. We recommend cool ash removal as a safety factor to the customer. The word
HOT – usually lends the customer to believe that the vacuum is indestructible
and it does have limitations as to how much heat and especially the amount of
burning materials that can be taken out of a stove. The customer needs to
exercise good common sense in this decision.
| |
| |
|
|
